CISCO AIR WIRELESS LAN CONTROLLER CONFIGURATION LAB part 1

CISCO WIRELESS LAN CONTROLLER CONFIGURATION

Objective;

1.    Configure a cisco WLC using CLI setup wizard   

2.    Connect to the Controller using Web interface

3.    Allow telnet connections to the controller

4.    Create a WLAN with open authentication

5.    Create a DHCP scope to support local clients

6.    Verify AP

7.    Connect to new WLAN

1. Management interface 10.1.1.100/24 AP uses this interface to discover

controller

2. AP Manager interface 10.1.1.101/24 Used for L3 comms to all AP- now gone

3. Service port interface Used for OOB management 192.168.0.200/24

887 Router configuration

Interface
fastEthernet 3

Description
trunk link to 2960switch1

Switchport
mode trunk

!

Interface
fastEthernet 0

Description
access link to internet

Switchport
mode access

Switchport
access vlan 1

!

Interface
vlan 1

Description
VLAN 1 SVI to internet

Ip
address 192.168.0.202 255.255.255.0

Ip nat
outside

!

Interface
vlan 10

Description
default gateway for WLAN10

Ip
address 10.1.1.1 255.255.255.0

Ip nat
inside

!

Interface
vlan 20

Description
default gateway for WLAN20

Ip
address 20.1.1.1 255.255.255.0

Ip nat
inside

!

Ip nat
inside source list 1 interface vlan1 overload

!

access-list
1 permit 10.0.0.0 0.255.255.255

access-list
1 permit 20.0.0.0 0.255.255.255

Ip
route 0.0.0.0 0.0.0.0 vlan1 192.168.0.1

!

2960 Switch Configuration

vlan
10

 name WLAN10

!

vlan
20

 name WLAN20

!

interface
FastEthernet0/1

Description
link to router fastEthernet3

 switchport mode trunk

!

interface
FastEthernet0/2

description
link to wireless AP1

 switchport access vlan 10

!

interface
GigabitEthernet0/1

description
link to WLC1

 switchport mode trunk

!

interface
vlan 1

description
OOB management of switch

ip
address 192.168.0.201 255.255.255.0

!

ip
default-gateway 192.168.0.1

CONTROLLER CONFIG

Controller Management interface IP	10.1.1.100/24
AP manager interface	10.1.1.101/24
Service port for OOB	192.168.0.200/24
2960 switch  OOB	192.168.0.201/24
887 Router  OOB	192.168.0.202/24
887 VLAN 10 IP	10.1.1.1/24
887 VLAN 20 IP	20.1.1.1/24
WLAN10	SSID
WLAN20	SSID
Controller DHCP scope VLAN 10	10.1.1.10 – 10.1.1.20
Controller DHCP scope for VLAN 20	20.1.1.10 – 20.1.1.20

System Name [Cisco_8a:6c:23] (31characters max): WLC1

Enter Administrative User Name (24characters max): admin

Enter Administrative Password (3 to 24 characters): Cisco12345

Re-enter Administrative Password: Cisco12345

Service Interface IP Address
Configuration [static][DHCP]: static

Service Interface IP Address Configuration: 192.168.0.200

Service Interface netmask: 255.255.255.0

Enable Link Aggregation (LAG) [yes][NO]: NO

Management Interface IP Address: 10.1.1.100

Management Interface Netmask: 255.255.255.0

Management Interface Default Router: 192.168.0.1

Management Interface VLAN Identifier (0 = untagged): 10

Management Interface Port Num [1 to 2]: 1

Management Interface DHCP Server IP Address: 10.1.1.100

AP Manager Interface IP Address: 10.1.1.101

AP-Manager is on Management subnet, using same values

AP Manager Interface DHCP Server (10.1.1.100):

Virtual Gateway IP Address: 1.1.1.1

Mobility/RF Group Name: RGGROUP1

Network Name (SSID): WLAN10

Configure DHCP Bridging Mode [yes][NO]: NO

Allow Static IP Addresses [YES][no]: YES

Configure a RADIUS Server now? [YES][no]: NO

Warning! The default WLAN security policy requires a RADIUS server.

Please see documentation for more details.

Enter Country Code list (enter 'help'
for a list of countries) [US]: GB

Enable 802.11b Network [YES][no]: YES

Enable 802.11a Network [YES][no]: YES

Enable 802.11g Network [YES][no]: YES

Enable Auto-RF [YES][no]: YES

Configure a NTP server now? [YES][no]: YES

Enter the NTP server's IP address: 10.1.1.1

Enter a polling interval between 3600 and 604800 secs: 3600